Chucklemonkey Posted May 19, 2010 Report Share Posted May 19, 2010 Hello all, having never pinned a model in my life I was just looking for some advice and info. Firstly, what is actually used as the pin? I understand it is a small metal rod but what and where do I actually ask for this? Is it something I should get in a hardware store or is it a material best sourced from gaming shops/websites? Secondly, and this is particularly relevant to the cherub, my intention would be to pin it to a scenic element on the base to give the appearance of flight, in doing so however it would seem that the entire model's weight would bear down on the pin. Is this feasible, or would the model weigh too much for the pinning material? Sorry for what may be basic questions, really coming to this blind. Thanks for taking the time to read this. Quote Link to comment Share on other sites More sharing options...
Baron M Posted May 19, 2010 Report Share Posted May 19, 2010 Hi, - You need a pin vice(or Dremel type multi-tool) to hold the drill bits. - Drill bits. + I'd use brass wire for the pinning, and you'll need snips to snip it. -I used to get all that from a model shop, often model railway/remote control car shops sell these items (or a GW store). -Practice on a few old figs you're not precious about first! Quote Link to comment Share on other sites More sharing options...
Baron M Posted May 19, 2010 Report Share Posted May 19, 2010 -The cherub's a relatively light model. -The difficulty will be in cleanly drilling into the feet/wings (if that's your intention). I made the cherub (was particularly pleased with the wings)! It's a pain, but if you're serious about getting good results, you'll need to spend some dosh on preparatory tools. - When I first got into minis, I used (don't do this at home!!) one of my Mums kitchen knives to remove flash, great blobs of araldite to gunge things together(don't do that either!). -You should get plenty of useful advice on here! Quote Link to comment Share on other sites More sharing options...
Brushmistress Posted May 19, 2010 Report Share Posted May 19, 2010 Hi, - You need a pin vice(or Dremel type multi-tool) to hold the drill bits. - Drill bits. + I'd use brass wire for the pinning, and you'll need snips to snip it. -I used to get all that from a model shop, often model railway/remote control car shops sell these items (or a GW store). -Practice on a few old figs you're not precious about first! Pretty much dead on - the only thing I'd add is that you can also use cut up metal paper clips if you can't get a hold of tiny brass rods/wires. Quote Link to comment Share on other sites More sharing options...
Buhallin Posted May 19, 2010 Report Share Posted May 19, 2010 I use paper clips for most of my pinning. For especially delicate pins I use real-life straight pins - snip the point and the head, and you've got a surprisingly strong bit of very thin metal. Quote Link to comment Share on other sites More sharing options...
Chucklemonkey Posted May 19, 2010 Author Report Share Posted May 19, 2010 I use paper clips for most of my pinning. For especially delicate pins I use real-life straight pins - snip the point and the head, and you've got a surprisingly strong bit of very thin metal. I like this pin idea it would seem to me to be somewhat sturdier than paper clips, will check out brass strips also. Think it's a trip out to see about buying a dremel also... Thanks to all for the help. Well, except you brushmistress, I know your opinion on cats, grrrr... Seriously,thanks all.:hail: Quote Link to comment Share on other sites More sharing options...
Buhallin Posted May 19, 2010 Report Share Posted May 19, 2010 I would NOT suggest using a Dremel for pinning. Most Dremels are very, VERY high RPM, and there's a lot of potential for damage if the bit binds, and even if it doesn't that much speed will heat the metal up quickly. If you want power tools, a standard power drill is a bit bulky, but does the job as it's far more controllable at slow speeds. Realistically though, you're better off with a simple hand-worked pin vise. Make sure you get one with a rotating head, and you'll be fine. Unless you're doing a LOT of pinning or very large models, doing it by hand goes pretty quickly. Quote Link to comment Share on other sites More sharing options...
Melnibonean Posted May 19, 2010 Report Share Posted May 19, 2010 (edited) A pic so you can see the results. I used a regular pin with the piont and head nipped of (as dscribed above). IIn this instant I drilled into its butt. I have alot of experience but the limbs on the cherub are to tiny and easy to damage. There's no issue with the weight. This is a very light figure and the pin is strong. Just make sure you dill into the figure about 3mm. I painted the pin silver. Black stands out to much. Edited May 19, 2010 by Melnibonean Quote Link to comment Share on other sites More sharing options...
Chucklemonkey Posted May 20, 2010 Author Report Share Posted May 20, 2010 Well it all came together tonight, someone at my gaming group had a spare pin vice and I jumped in. I have to say I think it looks pretty good for a first effort, will post pics next weeks. I also drilled into the butt as it did seem the safest place! Quote Link to comment Share on other sites More sharing options...
tenabrae Posted May 20, 2010 Report Share Posted May 20, 2010 I did similar to melniboenean but I pinned in a GW flying stand (cut the top off, pinned it to his bum) rather than just use the metal rod. Quote Link to comment Share on other sites More sharing options...
The Strange Dude Posted May 21, 2010 Report Share Posted May 21, 2010 I use this for pins http://www.bitsandkits.co.uk/armature-pinning-wire-x10-p-3980.html has the advantage that it is exactly 1mm in diameter allowing a good snug fit with holes made with 1mm bit (unlike paperclips and the ilk which tend to be thinner and wallow in the hole a bit). As to pinning itself it seems really hard at first but with a little practice you'll soon realise you can pin almost anything (I've drilled the middle out of 1.5mm plastic rod to make sniper rifle barrels).Like anything else practice makes perfect. Quote Link to comment Share on other sites More sharing options...
tenabrae Posted May 21, 2010 Report Share Posted May 21, 2010 I use this for pins has the advantage that it is exactly 1mm in diameter allowing a good snug fit with holes made with 1mm bit (unlike paperclips and the ilk which tend to be thinner and wallow in the hole a bit). You can buy 1mm paperclips (here in aus at least). I use 'normal' paperclips and drill with a .85mm bit (which is a number 66 bit in many manufacturer's ranges). Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.